Note: This article contains affiliate links. If you click on these links and make a purchase, I may earn a small commission at no extra cost to you. This helps support my research and content. Read my full affiliate disclaimer here.
If your Honda Fit is showing signs of vibration, uneven tire wear, or hub noise, choosing the right wheel hub assembly matters for safety and drivability. You want a durable unit that matches factory fitment and restores proper wheel alignment and bearing performance. This guide highlights the top shortlisted wheel hub assemblies for the Honda Fit. We evaluated candidates on durability, fitment accuracy, and bearing quality to help you narrow your options. Read on for the features and factors that matter most when replacing a wheel hub assembly.
Looking for other parts? See all Honda Fit parts & accessories.
Top Picks at a Glance
1. MOOG 512544 Wheel Bearing and Hub Assembly
| Brand | MOOG |
|---|---|
| Material | Alloy Steel |
| Bearing Number | 512544 |
| Bearing Type | Wheel Bearing |
This MOOG 512544 hub assembly is a complete wheel bearing and hub unit intended as a direct factory-replacement to restore wheel support and wheel-speed sensing. It installs in place of the original hub and is typically used when a worn bearing causes noise, vibration, or ABS/traction faults. Notable features include a precision roll-form bearing design for consistent preload, a quad lip seal to keep water and dirt out, and coated studs to resist rust and simplify later removal. For a reliability-focused buyer the benefits are straightforward: application-specific raceway geometry and rigorous testing aim to extend service life and reduce premature wear, while the unit arrives ready to bolt on for a relatively quick swap. Limitations are that this is a single replacement hub so matching the opposite side is advisable for balanced wear, and installation still requires basic mechanical tools and attention to ABS sensor handling. Fitment should be confirmed for the exact Honda Fit year and trim before ordering.
Best for: A reliability-focused buyer who prioritizes a durable, factory-quality replacement to eliminate bearing noise and restore safe wheel operation on their Honda Fit.
Less Ideal for: Budget DIYers who prefer the lowest-cost parts for short-term fixes or owners wanting a generic universal hub rather than a vehicle-specific factory-quality replacement.
- Complete hub-and-bearing assembly for direct replacement to restore wheel support and ABS signal alignment
- Precision roll-form bearing design to maintain proper preload and reduce noise
- Quad lip seal and coated studs provide improved protection against moisture, dirt, and rust
- Engineered for straightforward installation to shorten downtime
- Sold as a single hub assembly so replacing only one side can leave uneven wear characteristics
- Requires correct year/trim fitment verification and basic mechanical skill to install
Verdict A dependable, factory-style hub assembly built for long service life and straightforward replacement when you need a reliable fix for a Honda Fit wheel bearing problem.
2. TRQ Rear Wheel Bearing & Hub Assembly Set (2‑Piece) for 2015–2020 Honda Fit
| Bearing Type | Ball Bearing |
|---|---|
| Material | Alloy Steel |
| Fitment Years | 2015-2020 Honda Fit |
| Quantity | 2 Piece (rear driver & passenger) |
This TRQ two-piece rear wheel bearing and hub assembly set is a direct-fit replacement intended to swap into the rear driver and passenger sides of a 2015–2020 Honda Fit. Each assembly arrives pre-assembled to simplify installation and reduce time in the garage, and TRQ supplies DIY videos to guide owners through the job. The assemblies use ball bearings and factory-style machined surfaces that aim to restore wheel smoothness, reduce vibration, and keep ABS signals working when the original unit has failed. Most users report straightforward fitment and quiet operation after installation, though there are occasional reports of early failures or incorrect wheel stud specifications on some units. Expect an easier DIY replacement compared with rebuilding bearings, and be prepared to inspect studs and sensor fitment during install. For owners prioritizing convenience and a fast, direct swap, this kit covers both rear sides and minimizes hassle, but those wanting the highest-end bearing brands may prefer alternative name-brand options.
Best for: Convenience-driven Honda Fit owners who want a quick, direct replacement to fix rear wheel noise or play without rebuilding bearings or sourcing individual parts.
Less Ideal for: Buyers seeking top-tier OEM-brand bearings for heavy-duty or high-mileage applications should consider premium alternatives or dealer-sourced assemblies.
- Sold as a two-piece kit covering both rear driver and passenger sides for one job
- Pre-assembled hub assemblies reduce installation time and eliminate bearing repacking
- Includes DIY installation videos to help convenience-focused owners complete the repair
- Designed as direct-fit replacements for 2015–2020 Honda Fit rear applications
- Some buyers reported early failures or metal debris in bearings on isolated units
- A few units have incorrect or short wheel studs requiring reuse of original studs
Verdict A convenient, pre-assembled two-piece rear hub kit made to simplify DIY replacement on 2015–2020 Honda Fit models, with generally good fitment but occasional quality variations.
3. TadaMark Front Steering Knuckles with Wheel Bearing Hub Assembly for Honda Accord 2003–2007 (26-Spline, Automatic)
| Fitment | 2003–2007 Honda Accord L4 2.4L (Automatic) |
|---|---|
| Spline Quantity | 26 |
| Material | Heat-treated drop forged steel |
| Hub Included | Yes |
| Bearing Included | Yes |
This TadaMark steering knuckle and hub assembly replaces the front left and right factory units on 2003–2007 Honda Accord 2.4L cars with automatic transmissions and 26-spline axles. It is a ready-to-install assembly that includes the wheel hub and bearing and is built from heat-treated drop forged steel to resist bending under suspension loads. Typical use is direct replacement during front-end repair or when diagnosing vibration, uneven tire wear, or steering play caused by worn knuckles or bearings. Buyers will appreciate the included hub and bearing which shortens install time compared with sourcing parts separately, and the claimed hardness and toughness for longevity under performance driving and heavier loads. Limitations to note are fitment restrictions to automatic transmissions and 26-spline axles only, and mixed user reports about quality control and occasional damaged or faulty ball joints, so inspect parts on arrival and torque fasteners per factory procedure. Some purchasers also recommend swapping the supplied cotter pin for a stronger aftermarket unit.
Best for: Performance-oriented owners who prioritize restoring precise steering feel and durability under spirited driving and want a near-direct factory-replacement assembly for 2003–2007 Accord 2.4L automatics.
Less Ideal for: Owners with manual transmissions, 28-spline axles, or those seeking an exact OEM-sourced part from a dealership should look elsewhere.
- Complete hub and bearing included for faster, cleaner installation
- Heat-treated drop forged steel construction for improved strength under load
- Sold as a left and right pair so both sides can be replaced together
- Direct-fit replacement for specified model years and engine to simplify sourcing
- Compatible only with automatic transmission and 26-spline axles so it will not fit all Accords of these years
- Some customer reports of shipping damage or ball joint failures indicate inconsistent quality control
Verdict A strong, ready-to-install hub-and-knuckle pair aimed at performance-focused Accord owners, but confirm transmission and spline count and inspect for shipping damage on arrival.
4. PAROD Rear Wheel Hub Bearing Assembly for Honda Pilot 2009–2015 FWD
| Fitment | Honda Pilot 2009-2015 Rear FWD |
|---|---|
| Manufacturer | PAROD |
| Manufacturer Part Number | 512416 |
This PAROD rear wheel hub bearing assembly is a direct-fit replacement intended for Honda Pilot 2009–2015 FWD applications and is positioned as an affordable alternative to factory parts. It combines a pre-mounted bearing and hub so you replace the whole assembly rather than pressing bearings in, which simplifies installation for DIY mechanics and independent shops. The listing emphasizes factory-quality performance and vehicle-tested fit to maintain proper wheel guidance and load support, so you should expect normal road handling and quiet operation when installed correctly. Practical benefits include the convenience of a complete hub assembly and a lower upfront cost compared with branded factory replacements. Limitations are typical for budget aftermarket parts: long-term durability and exact match to OEM tolerances can vary by unit, and professional installation is recommended if you lack tools or experience to ensure torque and alignment are correct. For routine repairs on older Pilots this assembly offers a cost-effective way to restore wheel function while keeping labor straightforward.
Best for: Budget-conscious owners focused on restoring safe wheel function on a Honda Pilot 2009–2015 FWD without paying for a premium OEM-brand assembly.
Less Ideal for: Drivers seeking a long-term, warranty-backed factory-branded replacement or those who prioritize maximum longevity for high-mileage or heavy-duty use should consider higher-end options.
- Complete hub and bearing pre-assembled for faster replacement
- Marketed to match factory-level fit and basic performance
- Lower-cost option compared with brand-name factory-replacement hubs
- Fits Honda Pilot 2009–2015 FWD without modification
- Long-term durability and tolerance matching may vary compared with factory-brand parts
- May require professional installation to ensure correct torque and alignment
Verdict A cost-effective, pre-assembled hub to get a 2009–2015 Honda Pilot FWD back on the road quickly, with typical budget-part compromises in long-term durability.
5. Youxmoto Front Wheel Hub Bearing Steering Knuckle Assembly (pair) for Honda Accord 2003–2007, Automatic 26-Spline
| Fitment years | 2003–2007 |
|---|---|
| Engine | 2.4L L4 |
| Transmission note | Automatic transmission only |
| Spline quantity | 26 |
This two-piece kit replaces the front steering knuckle and integrated wheel hub bearing for vehicles that require a 26-spline automatic-axle fitment. It is intended to restore wheel support and steering geometry when a worn or damaged hub or knuckle is causing noise, vibration, uneven tire wear, or loose steering. The assemblies come preassembled to simplify installation compared with swapping separate bearings and knuckles, and the product description highlights a protective coating to resist rust. Buyers should expect typical installation at the front left and right positions and should verify spline count and transmission type before purchasing. Reported benefits include a snug fit and quieter operation for some users, but customer feedback also shows inconsistent sizing and several serious reports of component or fastener failure, which raises safety concerns and suggests variable quality control. For a risk-averse buyer looking for dependable replacement parts, confirm exact fit and inspect hardware carefully during installation or consider a factory-quality alternative if fitment or build consistency is critical.
Best for: A risk-averse mainstream buyer who prioritizes restoring safe, factory-like steering and wheel support and wants a ready-to-install replacement for a specific confirmed vehicle fitment.
Less Ideal for: Buyers who cannot confirm spline count and transmission type, or who prefer guaranteed factory-quality parts and dealer-backed replacements should consider other options.
- Ships as a preassembled knuckle and hub pair for easier front-end replacement
- Specifies exact fitment by year, engine and 26-spline automatic axle to reduce ordering mistakes
- Protective coating to slow corrosion for longer service life in typical road conditions
- Can address common symptoms like wheel noise, vibration, and uneven tire wear when correctly fitted
- Fitment appears inconsistent for some buyers leading to clearance or sizing problems
- Multiple user reports describe fastener or joint failures that indicate variable manufacturing quality and potential safety risk
- Not suitable for manual-transmission or non-26-spline axles without modification
Verdict Preassembled hub-and-knuckle pair can simplify a front-end replacement but inconsistent sizing and reports of failures mean cautious fit verification or a factory-quality alternative is recommended.
6. Youxmoto Front Right Steering Knuckle with Wheel Bearing Hub Assembly for 2003–2005 Honda Civic 1.7L (Passenger Side)
| Fitment | 2003–2005 Honda Civic 1.7L, front right passenger side |
|---|---|
| Replace part numbers | 698-494, 698494, 51210S5AJ30, 45255S01A00, 44600S5DA00 |
| Manufacturer | Youxmoto |
This Youxmoto assembly combines the steering knuckle, wheel bearing and hub into a single passenger-side replacement for 2003–2005 Honda Civic 1.7L models. It is sold as a plug‑and‑play unit intended to simplify repairs by removing the need to press bearings or reuse old components; installers report straightforward fitment and shorter shop time compared with rebuilding the original hub. The part is marketed with a protective coating to resist rust and a preinstalled ball joint, which helps reduce installation steps and get the car back on the road faster. Practical benefits include time savings, lower labor complexity, and a one‑piece replacement that addresses wheel play, uneven tire wear, and steering vibration. Potential downsides are occasional fitment variance reported by some users that required a professional alignment, and the product is an aftermarket replacement rather than a factory part, so long‑term durability may differ from a factory-quality unit. Buyers should verify the part numbers and vehicle year before ordering to ensure correct compatibility.
Best for: Practical optimizers who want a cost-effective, time-saving replacement that minimizes shop labor and simplifies a front passenger-side hub repair on a 2003–2005 Honda Civic 1.7L.
Less Ideal for: Buyers seeking an exact factory-origin component or guaranteed OEM longevity should consider a factory-quality replacement or dealer part instead.
- One-piece knuckle and hub assembly reduces installation time and avoids bearing press work
- Preinstalled ball joint and hub provide plug-and-play convenience for the passenger-side repair
- Protective coating helps resist rust and corrosion for longer service life in typical road conditions
- Multiple listed replacement part numbers match common Honda Civic references for straightforward cross-checking
- Aftermarket fitment can vary and may require a professional alignment after installation
- Not a factory-quality part so long-term durability may differ from an OEM replacement
Verdict A convenient, budget-friendly one-piece hub and knuckle for 2003–2005 Honda Civic 1.7L that saves installation time but may require alignment and offers aftermarket rather than factory-level pedigree.
7. Youxmoto Front Left Steering Knuckle & Wheel Bearing Hub Assembly (Front Left)
| Compatible models | Honda Accord 2008–2012; Acura TSX 2009–2014 |
|---|---|
| Position | Front left drive side |
| Replace part numbers | 698-447; LK051; 44300TA0A61; 44300TA0A62; 44600TA0A00; 45255TA0A00; 51215TA0020 |
| Manufacturer | Youxmoto |
This steering knuckle with integrated wheel bearing hub replaces the front left drive-side assembly and is intended as a direct replacement for compatible Honda Accord and Acura TSX model years. It installs in place of the factory unit and addresses symptoms such as wheel noise, uneven tire wear, or looseness by restoring hub support and wheel bearing function. The part ships with the lower ball joint preinstalled and a corrosion-resistant coating to help with longevity. Buyers should expect to press bearings and ball joints during installation and to reuse some fasteners in certain cases. Several users report straightforward fitment on 2010 Accords, while others noted the bearing sometimes needs full seating and that the upper ball joint is not included. This is a practical replacement for someone doing a hub/knuckle swap or repairing a worn bearing, but plan for a press, basic suspension tools, and the possibility of reusing an axle nut or upper joint when removing the old knuckle.
Best for: Balanced owners who want a practical, ready-to-install replacement that restores steering and hub function without chasing multiple separate parts.
Less Ideal for: Drivers seeking a complete plug-and-play swap with every fastener and both ball joints included should look for a kit that lists all hardware and both joints explicitly.
- Integrated hub and bearing reduces installation steps compared with separate parts.
- Coated finish resists rust and corrosion for longer service life.
- Ships with lower ball joint installed to simplify assembly of the lower suspension connection.
- Direct-fit design listed for specific model years to reduce trial-and-error fitment issues.
- Upper ball joint is not included so additional parts or replacement may be needed during installation.
- Some units may require pressing the bearing fully into place which can add labor and tool needs.
- Occasional reports of reused fasteners or axle hardware being necessary rather than included.
Verdict A practical, coated front-left knuckle and hub assembly that fits listed Accord/TSX years and simplifies a bearing/hub replacement, but plan for pressing operations and possible extra hardware.
Choosing the Right Honda Fit Wheel Hub Assembly: Key Factors to Consider
Correct Fitment for Honda Fit
Proper fitment ensures the assembly aligns with the vehicle's hub flange, wheel studs, and any ABS or wheel-speed sensor interfaces. Mismatched fitment can lead to alignment issues, accelerated tire wear, or improper ABS signals.
When assessing fitment, check bolt pattern, stud size and pitch, and whether the assembly is intended for front or rear use. Correct fitment reduces installation time and lowers the risk of post-install problems that can affect steering feel or vehicle safety.
Bearing Type and Durability
The bearing inside the hub assembly determines load capacity and expected service life. Sealed, pre-pressed bearings are common and reduce the chance of contamination during installation, while open designs may require additional maintenance.
Look for bearings with appropriate load ratings, quality cage materials, and proven tolerances. Durability affects how the hub handles everyday driving loads, potholes, and lateral forces, which in turn influences noise and vibration over time.
Sealing and Contaminant Protection
Effective seals keep water, dirt, and road salt away from the bearing surfaces. Poor sealing is a leading cause of premature bearing failure and noisy operation.
Consider assemblies with robust lip seals and corrosion-resistant coatings on mating surfaces. Reliable sealing preserves lubrication, reduces maintenance needs, and helps the assembly maintain consistent performance in wet or salty environments.
ABS Tone Ring and Sensor Compatibility
Many modern vehicles use a tone ring integrated into the hub assembly to provide wheel-speed data to the ABS system. Proper alignment and ring integrity are critical for accurate sensor readings and consistent ABS function.
Verify whether the assembly includes a tone ring or is designed to work with the Fit's existing sensor. Misaligned or damaged tone rings can trigger ABS warnings and affect braking behavior, so compatibility is a key selection factor.
Material Quality and Corrosion Resistance
Hub housings and flanges exposed to road salt and moisture require materials and coatings that resist rust and pitting. Corrosion can make future removal difficult and compromise structural integrity.
Choose assemblies with durable metallurgy and protective finishes such as zinc plating or other anti-corrosion treatments. Higher-quality materials also contribute to consistent torque retention at mounting points and better long-term reliability.
Ease of Installation and Included Hardware
Ease of installation affects labor time and the risk of installation-related issues. Assemblies that come with pre-pressed bearings, new studs or mounting hardware, and clear instructions reduce the chance of errors during replacement.
Consider whether the assembly requires special tools or press operations. Units designed for bolt-on installation with included components typically simplify the process and lower the chance of contamination or rework during service.
FAQ
How can I tell if my Honda Fit needs a wheel hub assembly replacement?
Common signs include humming or grinding noises from the wheel area, vibration during driving, uneven tire wear, or an illuminated ABS warning. Symptoms often worsen with speed or when turning. A professional inspection can confirm bearing play or excessive runout before ordering a replacement.
Can I replace a wheel hub assembly myself?
Replacing a hub assembly is possible for experienced DIYers with the right tools and a safe workspace. It usually involves lifting the vehicle, removing the wheel and brake components, and unbolting the hub from the knuckle. Some assemblies are bolt-on and simplify the job, while others may require a press. If you are unsure about torque specs or ABS sensor handling, consider professional service.
Should I replace front and rear hubs at the same time?
It depends on inspection findings and the vehicle's mileage. Hubs do not always fail simultaneously, so replacing only the worn side is often acceptable. However, if one hub shows significant wear or contamination, it is worth inspecting the opposite side and addressing both if signs of similar age or damage are present to maintain consistent handling.
How long do wheel hub assemblies usually last?
Lifespan varies with driving conditions, load, and maintenance, but assemblies often last many tens of thousands of miles under normal use. Exposure to heavy moisture, road salt, or rough roads can shorten service life. Regular inspections help detect early signs of wear before failure occurs.
Will a bad hub assembly affect braking or ABS performance?
Yes, a degraded hub can impact ABS if the tone ring or sensor signal is compromised, and excessive play can change rotor alignment. That can lead to ABS warnings or altered brake feel. Addressing hub issues promptly helps preserve reliable braking performance.
What should I bring to a mechanic when having a hub replaced?
Provide the vehicle year and trim details, and describe the symptoms you observed. If you prefer a specific type of assembly build or sealing standard, mention that. Clear symptom information helps the technician confirm fitment and select the correct hub for the Honda Fit.
How We Chose the Best Honda Fit Wheel Hub Assembly
We focused on items designed specifically for the Honda Fit and prioritized fitment, bearing durability, sealing against contaminants, and compatibility with ABS sensors where applicable. Key evaluation criteria included bearing type and load ratings, hub material and corrosion protection, seal and lubrication quality, ABS tone ring integrity and alignment, and ease-of-installation features such as pre-pressed bearings and included hardware. We excluded products that did not list explicit fitment for the Honda Fit, assemblies with unclear bearing specifications, and options lacking clear sealing or ABS provisions. We also filtered out units with inconsistent quality feedback on long-term bearing life. The resulting shortlist reflects components that balance reliable fitment, serviceability, and expected longevity for typical driving conditions.
Our full evaluation process is outlined in our review methodology.
Conclusion
When choosing a wheel hub assembly for a Honda Fit, prioritize correct fitment, bearing durability, and proper sealing to restore smooth steering and prevent premature failure. Verify ABS compatibility if your vehicle relies on a tone ring. Tradeoffs usually involve ease of installation versus long-term durability. Aim for an assembly that balances robust materials and seals with accurate fitment and straightforward installation to get reliable performance for years of driving.
Explore More:
- Check out all Honda Fit parts & accessories
- Explore Wheels & Tires
- Browse all Auto Parts
