Note: This article contains affiliate links. If you click on these links and make a purchase, I may earn a small commission at no extra cost to you. This helps support my research and content. Read my full affiliate disclaimer here.
Replacing a worn engine mount can noticeably cut vibration, reduce drivetrain wear, and restore comfortable driving in your Ram 3500. You want a solution that holds the engine securely under load, isolates noise and vibration, and stands up to towing and heavy-duty use. This guide presents seven shortlisted options that meet those needs and explains the criteria used to evaluate them. Read on to understand the key tradeoffs and which features matter most when choosing a Ram 3500 engine mount.
Top Picks at a Glance
1. A-Premium 3-Piece Engine and Transmission Mount Set for Ram 2500/3500 6.7L
| Vehicle fitment | Ram 2500 2013-2018 6.7L; Ram 3500 2013-2018 6.7L (3500 2018 4WD only) |
|---|---|
| Set contents | Front left motor mount, front right motor mount, rear transmission mount |
| Manufacturer | PremiumpartsWhosale |
| Manufacturer Part Number | APEM1283 |
This A-Premium three-piece mount set replaces the front left, front right motor mounts and the rear transmission mount on 6.7L Ram 2500 and 3500 models from the specified years. It is used during a powertrain mount refresh to restore proper engine positioning, reduce vibration and road noise, and prevent excess movement that can stress driveline components. The kit claims precise fitment for the listed Ram applications and is made with reinforced components intended for long service life. Installation is a standard mechanical job for a qualified technician and the set supports both automatic and manual transmissions (note the 2018 3500 fitment is for 4WD only). Practical benefits include a firmer, quieter ride and the convenience of replacing all three primary mounts at once instead of sourcing individual parts. Limitations are that fitment is specific to the stated years and configurations, and buyers should verify compatibility with their truck build before ordering since it will not cover RWD or FWD variants where excluded.
Best for: A reliability-focused buyer who wants a straightforward replacement kit to restore proper engine support and reduce vibration without sourcing multiple parts separately.
Less Ideal for: Drivers seeking a one-off advanced performance mount or those with Ram configurations outside the listed years and drive types should consider other options.
- Three-piece kit replaces both motor mounts and the rear transmission mount for a complete mount refresh
- Engineered for precise fitment to the listed 6.7L Ram models to minimize installation adjustments
- Designed to reduce engine vibration and road noise for a smoother driving experience
- Compatible with both automatic and manual transmissions for the covered model years
- Fitment is limited to the specified Ram model years and 2018 3500 only fits 4WD, requiring careful verification before purchase
- No detailed material or lifetime durability data beyond the one-year guarantee is provided
Verdict A convenient, reliability-minded three-piece mount kit for restoring engine support and reducing vibration on compatible 6.7L Ram 2500/3500 trucks when fitment is confirmed.
2. A-Premium 3‑Piece Engine and Transmission Mount Kit for Dodge Ram 2500/3500 5.9L
| Set Name | Set of Three |
|---|---|
| Item model number | APEM1003 |
| Manufacturer Part Number | APEM1003 |
| OEM Part Number | A5410, A5478, 3254, 3376, EM-4018, EM-4060, 52021712AA, 52021713AA, 52122714AB, 52121773AA, 52121774AA, 52121774AB, 52121774AD, 52021713AB |
This three-piece kit replaces the front left and right motor mounts plus the transmission mount for Dodge Ram 2500/3500 5.9L trucks and is intended for owners who need a direct replacement for worn mounts. The mounts are sold as a matched set so you can swap all major mounting points in one job, which speeds installation and restores engine alignment and vibration control. The listing cites rigorous testing and claims factory-quality fitment to common reference numbers, and customer comments report solid fit and near-OEM feel. Practical benefits include reduced engine movement under load, less vibration in the cab, and the convenience of buying mounts matched to the vehicle in a single package. Limitations are that the kit only fits the specified Ram years and engine/transmission combinations, and as an aftermarket option it may differ slightly from factory parts in feel or long-term durability compared with higher-end name-brand replacements.
Best for: Buyers who prioritize convenience and a quick, one-stop replacement for engine and transmission mounts on compatible Ram 2500/3500 trucks and want a straightforward swap to restore ride comfort.
Less Ideal for: Owners who need mounts for different model years, engines, or transmissions or who prefer OEM-brand parts with documented long-term mileage records.
- Sold as a matched three-piece kit so all main mounts can be replaced at once
- Designed to match factory reference numbers for straightforward fitment to specified Ram 2500/3500 models
- Customer feedback notes solid fit and reduced vibration after installation
- Fitment is limited to specific model years and the 5.9L/G56 transmission combination
- Aftermarket construction may not exactly match long-term durability of higher-priced factory-quality parts
Verdict A convenient matched three-piece mount kit that lets Ram 2500/3500 owners replace main engine and transmission mounts in one job, with fitment focused on the specified 5.9L model years.
3. 4M Auto Parts Engine & Transmission Mount 4‑Piece Set for Ram ProMaster 3500
| Brand | 4M Auto Parts |
|---|---|
| Manufacturer Part Number | 3533 3500 3505 3506 |
| OEM Part Number | 68264483AA / 68157408AB / 68157407AC / 68185879AA |
| Position | Left, Rear Lower |
This four-piece mount kit from 4M Auto Parts replaces the engine and rear lower torque strut mounts on Ram ProMaster 3500 3.6L vans. It is intended for direct replacement of the factory mounts and is used during engine or transmission service, or when vibration and drivetrain movement become noticeable. The set includes left rear lower and right engine mounts to restore proper engine alignment and reduce noise, vibration, and harshness. Built to aftermarket standards and described as designed under strict factory-quality guidelines, the kit aims to provide a like-for-like fit for manual and automatic 3.6L Promaster drivetrains. Practical benefits are firmer engine support, reduced driveline lash, and a straightforward swap-in install for technicians familiar with mount replacement. Limitations are typical of aftermarket kits: exact match to every factory tolerance is not guaranteed and fitment should be verified against the vehicle VIN and OEM part references before installation. The package is aimed at repair or performance-focused owners who want to restore solid mounting without sourcing multiple individual parts.
Best for: Performance-oriented Ram ProMaster 3500 owners who prioritize restoring firm engine support and reducing drivetrain movement to maintain drivetrain feel and handling under load.
Less Ideal for: Buyers seeking guaranteed factory-equivalent longevity or longevity-backed dealer replacement programs should consider dealer-sourced factory-quality mounts instead.
- Complete four-piece set replaces multiple mounts at once for coordinated drivetrain support
- Marketed to meet factory-quality design standards for a closer fit to original parts
- Covers left rear lower torque strut and engine mount positions to address common vibration points
- Supplies parts compatible with both manual and automatic 3.6L ProMaster drivetrains
- Aftermarket production means exact factory tolerances and longevity can vary from OEM parts
- Fitment spans multiple model years so buyers should confirm compatibility with their vehicle VIN before installing
Verdict A convenient four-piece aftermarket mount kit that restores firmer engine and transmission support on Ram ProMaster 3500 3.6L vans, best for owners focused on performance and reduced vibration.
4. JDMON 3‑Piece Engine and Transmission Mount Set for 2006–2008 Dodge Ram 2500/3500 5.9L
| Unit Count | 3.0 Count |
|---|---|
| Finish Type | Powder Coated |
| Manufacturer | JDMON |
| Included Components | 3PCS Engine Mount Transmission Mount |
This JDMON three-piece mount kit replaces the motor and transmission mounting points on 2006–2008 Dodge Ram 2500 and 3500 5.9L trucks to restore engine stability and reduce noise and vibration. Typically used when original mounts are cracked, collapsed, or allowing excessive engine movement, the kit installs in the engine bay to dampen torque reaction and isolate road and engine vibrations from the chassis. The mounts combine metal housings with rubber isolators and are powder coated for corrosion resistance. That construction should deliver acceptable durability for everyday driving and work use, and the three-piece set provides the common mounting locations you need in one purchase. Limitations are that this is an aftermarket budget option rather than a direct factory-branded part, so fit may require minor adjustment and professional installation is recommended for proper alignment and torque. Buyers should also confirm the exact factory part references before ordering to ensure compatibility with their truck's drivetrain and year range.
Best for: Budget-conscious Ram owners who need an affordable, complete mount set to restore engine stability and reduce NVH on older 5.9L trucks.
Less Ideal for: Owners seeking a factory-branded or performance-oriented mount with exact OEM fit and characteristics should consider higher-end or dealer-sourced replacements.
- Sold as a three-piece kit covering engine and transmission mount locations so you get multiple replacements at once
- Metal housings with rubber isolators provide standard vibration damping for daily driving
- Powder coated finish helps resist corrosion in underhood conditions
- Made to match several common factory part references for easier cross-referencing
- Aftermarket budget part so fitment may not be as precise as a factory-quality mount
- Requires professional installation for best results and correct alignment
Verdict A cost-focused three-piece mount kit that restores engine stability and reduces vibration for 2006–2008 Ram 2500/3500 5.9L trucks, but expect typical aftermarket fitment and professional installation.
5. SHICHU Set of 4 Engine Motor Mounts for Ram ProMaster 3.6L V6 (2014–2021)
| Compatible Vehicles | 2014-2021 Ram ProMaster 1500/2500/3500 3.6L V6 |
|---|---|
| Set Contents | Rear lower motor mount, rear torque strut, front left transmission mount, front right motor mount |
| Finish Type | Powder Coated |
| Model | CF5938 |
This SHICHU set supplies the four engine and transmission mounts needed when replacing worn mounts on a Ram ProMaster 3.6L V6. The kit includes the rear lower motor mount, rear torque strut, and both front transmission and motor mounts so you can replace the common failure points in one job. Finished with a powder coat, the mounts install using the original mounting points and are intended as factory-style replacements; buyers report they are slightly less firm than OEM, which can reduce transmitted vibration but may feel softer under hard acceleration. Installation is straightforward for a competent DIYer or a shop, and having all four pieces in one kit saves time sourcing parts. Limitations: the set is an aftermarket unit so firmness and long-term durability may vary compared with factory parts, and buyers should double-check fitment and part numbers for their specific model year and configuration before purchase.
Best for: Risk-averse mainstream buyers looking for a convenient, single-purchase replacement to restore normal engine support and reduce downtime after mount failure.
Less Ideal for: Drivers seeking exact factory-feel performance or those who want OEM-specified firmness for towing and heavy-duty use should consider factory-quality alternatives.
- Complete four-piece kit covers rear lower, rear torque strut and both front mounts so you can replace all common mount locations at once
- Powder coated finish helps resist corrosion during normal use
- Designed to bolt into factory mounting points for straightforward installation
- Aftermarket firmness is reported as softer than factory units which may affect engine feel under load
- Long-term durability and ride characteristics may differ from factory-quality mounts
Verdict A convenient four-piece aftermarket kit that gets a Ram ProMaster back on the road quickly, but expect a slightly softer feel than factory mounts.
6. Vinsyut Engine and Transmission Mount Set for Ram ProMaster 2014–2021 (4-piece)
| Vehicle fitment | Ram ProMaster 1500/2500/3500 3.6L V6 2014–2021 |
|---|---|
| Unit count | 4.0 Count |
| Manufacturer | vinsyut |
| Included components | engine mount set |
This Vinsyut 4-piece mount kit replaces the left and right engine mounts, the rear lower engine mount, and the transmission mount on Ram ProMaster 3.6L V6 vans from 2014–2021. It is intended as a direct replacement set for restoring engine support, reducing vibration at idle, and cutting drivetrain movement that causes clunks under acceleration or when shifting. The mounts use stamped steel housings and rubber bushings to balance comfort and control; that typically translates to noticeable reduction in cabin shake without making the powertrain feel excessively stiff. Buyers should plan for a moderate install: support the engine, swap mounts one at a time, and torque fasteners to spec at ride height. The kit covers common replacement positions so you can do a full refresh in one job, but long-term durability depends on install torque and driving conditions, and aftermarket rubber compounds can vary from factory-spec feel. Expect to verify fit against your vehicle's mount reference numbers before starting work.
Best for: Practical optimizers who want a cost-effective, single-purchase refresh to reduce vibration and drivetrain movement on their Ram ProMaster and prefer replacing multiple worn mounts at once.
Less Ideal for: Drivers seeking a long-term, performance-oriented upgrade or exact factory-match material properties should consider higher-end or factory-quality replacements instead.
- Complete 4-piece set replaces multiple mounts in one purchase for a full drivetrain refresh.
- Designed for Ram ProMaster 3.6L V6 2014–2021 so each piece targets common failure points.
- High-strength steel housings with rubber bushings aim to control engine movement while damping vibration.
- Includes left, right, rear lower engine, and transmission mounts to simplify a single-service replacement.
- Aftermarket rubber compound and weld quality can vary compared with factory-quality parts, affecting long-term longevity.
- Requires proper engine support and torqueing at ride height; installation is moderate and may need a mechanic for less-experienced DIYers.
Verdict A budget-friendly full mount kit that restores smoother operation for Ram ProMaster 3.6L vans, best for owners wanting a practical, single-service replacement rather than a premium performance upgrade.
7. JAVOUKA Engine & Transmission Mount Kit for Ram ProMaster 3.6L (1500/2500/3500, 2014–2021)
| Unit Count | 4.0 Count |
|---|---|
| Mounting Type | Floor Mount |
| Manufacturer | JAVOUKA |
| Style | for Promaster 3.6L 1500/2500/3500 14-21 |
This JAVOUKA mount kit replaces the engine and transmission mounts on Ram ProMaster 1500/2500/3500 3.6L models and is sold as a set of four pieces to return structural support and isolate vibration. Installation is intended as a direct replacement using factory-style mounting points, so mechanics can swap the mounts during routine service or a focused mount replacement job. The parts pair steel bracketry with rubber isolators to absorb engine movement and quiet driveline harshness, which users report improves NVH and resolves vibration-related symptoms. The kit lists multiple compatible part numbers and includes the common left, right, rear lower, and torque strut positions needed for a full repair. Expect a straightforward replacement for a vehicle-specific repair, but plan for moderate installation effort since alignment and torqueing are required and some buyers noted fit and installation fiddliness. The components aim to match factory performance while offering an affordable alternative for owners who want a complete mount refresh in one purchase.
Best for: Balanced all-round buyers who want a complete, vehicle-specific mount refresh to restore ride comfort and driveline stability without chasing individual parts.
Less Ideal for: Drivers looking for a premium, lifetime upgraded mount solution or those unwilling to handle a moderately involved install should consider professional installation or aftermarket performance mounts.
- Vehicle-specific kit covers left, right, rear lower, and torque strut mounts so you can replace all major engine/transmission supports at once
- Built with steel brackets and rubber isolators to reduce vibration and restore a firmer, quieter ride
- Designed as a direct factory-style replacement for Ram ProMaster 3.6L models, matching common OEM part numbers
- Multiple compatible part numbers listed makes it easier to verify fitment for the 2014–2021 ProMaster lineup
- May require moderate mechanical skill and careful alignment during installation, with a few buyers reporting fiddly fit
- Finish is unfinished steel so parts may benefit from corrosion protection depending on local climate
Verdict A complete, vehicle-specific mount kit that restores factory-style support and reduces vibration for Ram ProMaster 3.6L vans at an affordable value.
Choosing the Right Ram 3500 Engine Mount: Key Factors to Consider
Vibration Isolation
Effective vibration isolation is critical because it directly affects cabin comfort and component longevity.
A mount that isolates engine vibrations prevents resonance from transmitting into the frame and passenger compartment. Look for mounts designed with damping materials and geometries that absorb both high-frequency engine buzz and low-frequency torque pulses. Poor isolation can cause fatigue in nearby components, increase perceived noise, and make the truck feel rougher during idle and low-speed driving. Consider how the mount balances firmness for control with enough compliance to reduce transmitted vibration.
Load Capacity And Torque Resistance
Load capacity and torque resistance determine whether a mount can handle the forces generated during acceleration, towing, and heavy payloads.
Mounts must resist rotational forces that try to tilt or shift the engine under load. A mount engineered for higher torque resistance will maintain alignment and reduce stress on other drivetrain components. Check specifications for rated load or torque capacity where available, and favor designs that distribute forces across robust metal backing plates or reinforced housings. Underspecified mounts may deform over time, leading to misalignment and premature failure.
Material And Corrosion Resistance
Materials and corrosion protection affect durability, especially in regions with road salt or frequent exposure to moisture.
Mounts commonly use rubber, polyurethane, and metal; each material has different wear characteristics. Rubber offers good damping but can degrade from heat and oils, while polyurethane resists tearing and compression set but may transmit more vibration. Metal components should be treated or plated to resist rust. Consider the operating environment and select mounts with appropriate coatings and material choices to maximize service life in typical Ram 3500 use cases.
Fitment And Mounting Geometry
Accurate fitment and correct mounting geometry are essential for a trouble-free installation and reliable alignment.
A mount that matches the truck's bolt pattern and attachment points ensures the engine sits where intended, preserving driveline angles and minimizing stress on other mounts. Poorly fitting mounts can require modifications or lead to misalignment that exacerbates vibration and wear. Look for clear fitment documentation and designs that mirror factory mounting points to simplify installation and preserve drivetrain geometry.
Ease Of Installation
Ease of installation affects total downtime and whether you can perform the replacement yourself or need professional help.
Consider whether the mount requires special tools, supplemental brackets, or engine supports during removal and installation. Some designs facilitate bolt access and reuse of factory hardware, while others demand more invasive procedures. If you plan to DIY, favor mounts that are straightforward to install with common tools and clear instructions. Also factor in how motor mount signs and symptoms may guide you to replace multiple mounts at once to save labor.
Damping Characteristics And Ride Feel
Damping characteristics determine how the mount balances isolation with control and influence overall ride feel.
Stiffer mounts offer tighter engine control and reduced movement during acceleration, which can improve shift quality and reduce driveline lash. Softer mounts improve comfort by absorbing more vibration but may allow noticeable engine movement during hard acceleration. Consider the balance you prefer: a mount tuned for comfort versus one tuned for performance and load carrying. This affects perceived engine mount noise and long-term transmission of vibration into the chassis.
FAQ
What are common symptoms of a bad engine mount on a Ram 3500?
Common signs often include increased vibration at idle, noticeable engine movement under acceleration, and clunking or banging noises when shifting into gear. You may also notice uneven wear patterns on drivetrain components when a mount is failing. These symptoms usually signal loss of damping or structural integrity in the mount.
Can I replace a Ram 3500 engine mount myself?
It depends on your experience and tools. Some mounts are accessible and can be replaced with basic hand tools and an engine support, while others require lifting or temporarily supporting the engine and torqueing bolts to specific values. If you are unsure about procedures or torque requirements, professional installation is often recommended for safety and alignment.
How long do engine mounts typically last on heavy-duty trucks?
Lifespan varies with driving conditions and load, but mounts on heavy-duty trucks often last several years under normal use. Frequent towing, off-road use, and exposure to heat, oil, or road chemicals can accelerate wear. Regular inspection for cracking, deformation, and excess movement can help catch issues early.
Will a firmer mount reduce engine mount noise and vibration?
A firmer mount can reduce perceived engine movement and improve shift feel, but it may transmit more high-frequency vibration and noise into the cabin. The best choice balances firmness for control with enough damping to keep noise and vibration at acceptable levels for your use case.
Should I replace multiple mounts at once?
Often it makes sense to inspect all mounts and consider replacing more than one if they show similar age or wear. Replacing a single mount can shift load to older mounts and accelerate their failure. Coordinating replacements can save labor and restore balanced support across the drivetrain.
How We Chose the Best Ram 3500 Engine Mount
We focused on factors that directly affect long-term performance and real-world drivability for Ram 3500 owners. Primary evaluation criteria included vibration isolation performance to reduce cabin shake, structural durability and material quality for towing and heavy loads, mounting fit and bolt pattern accuracy for straightforward installation, and load capacity to handle the truck's torque and payload. We also considered corrosion resistance and warranty coverage as indicators of expected lifespan. Products with unclear fitment, low-rated durability, or lacking essential torque resistance were excluded. We prioritized mounts that balance robust construction with effective damping, and we filtered out options that did not meet factory-style mounting geometry or lacked clear specifications related to load ratings and material composition.
Our full evaluation process is outlined in our review methodology.
Conclusion
Choosing the right Ram 3500 engine mount means balancing vibration control, structural durability, and correct fitment. Prioritize mounts that provide the damping characteristics you need for comfort or load control while offering corrosion-resistant materials and enough torque capacity for towing. Weigh ease of installation and the likelihood of needing professional help against long-term durability. Inspect existing mounts for signs of wear and consider coordinated replacement to maintain drivetrain alignment and reduce future repairs.
