Note: This article contains affiliate links. If you click on these links and make a purchase, I may earn a small commission at no extra cost to you. This helps support my research and content. Read my full affiliate disclosure here.
Choosing the right brake calipers for your Mitsubishi Eclipse matters for safety and consistent pedal feel. The correct calipers ensure even pad wear, predictable stopping power, and long-term reliability under everyday driving or spirited use. This guide presents the top picks shortlisted for the Mitsubishi Eclipse, each selected for fitment accuracy, material quality, and resistance to corrosion.Below you will find concise notes on what to look for and the specific strengths that influenced our selections, followed by detailed product entries.
Looking for other parts? See all Mitsubishi Eclipse parts & accessories.
Top Picks at a Glance
1. cciyu Front Left & Right Brake Calipers Assembly with Brackets (19B2614C/19B2615C)
| Position | Front |
|---|---|
| Piston Count | 1 Piston |
| Piston Material | Iron |
| Bleeder Port Size | M10 x 1.0 |
| Inlet Port Size | M10 x 1.0 |
These cciyu front brake calipers replace the factory units on select Mitsubishi Eclipse and Galant models and come as a matched left and right pair with mounting brackets. They use a single iron piston design with M10 x 1.0 inlet and bleeder ports, and are supplied painted to resist corrosion out of the box. In use they perform as a straightforward direct-replacement component for routine brake repairs or rotor upgrades, restoring firm pedal feel and consistent stopping power. Notable features include matched components for balanced braking and a claimed quiet operation to reduce screeching. The calipers are packaged as two pieces so you get both driver and passenger side units ready to install, but they do not include pads or rotors so you will need to source those separately. Fitment is limited to the listed Mitsubishi models so confirm year and engine before ordering. For DIY mechanics and independent shops this is a cost-effective route to bring front braking back to factory-quality without specialty machining or modification.
Best for: A balanced all-round buyer who wants a dependable, factory-style front caliper replacement to restore braking performance without overspending or chasing specialty parts.
Less Ideal for: Drivers who need a complete brake kit including pads and rotors or those seeking performance-focused calipers for track use should consider other options.
- Supplied as a matched left and right pair with brackets for straightforward front-end replacement
- Painted finish provides basic corrosion resistance out of the box
- Single-iron piston design and standard M10 ports match factory plumbing for easy fitment
- Manufacturer states components meet or exceed factory specifications for reliable braking power
- Sold without brake pads or rotors so additional parts are required for a complete brake service
- Fitment is specific to listed Mitsubishi Eclipse and Galant years so compatibility must be verified
Verdict: A ready-to-install matched pair of painted front calipers that restore factory-style braking on supported Mitsubishi Eclipse and Galant models.
2. PowerStop Rear High-Temp Red Powder Coated Brake Caliper Pair (S1692)
| Auto Part Position | Rear |
|---|---|
| Item Type Name | Disc Brake Caliper Set |
| Material Type | Powder Coated |
| Included Components | Set of Calipers, Hardware |
These PowerStop rear calipers are a remanufactured, bolt-on replacement intended to upgrade the rear braking appearance and durability on compatible cars. They arrive as a matched driver and passenger pair with new boots, seals, guide pins, bleeder screws, pad hardware, and mounting brackets so installation is similar to a factory swap. The calipers are pressure tested and finished in high-temperature red powder coat with a clear topcoat to resist corrosion and maintain appearance behind aftermarket wheels. For performance-minded drivers the premium boots, silicone lube on slide pins, and included abutment clips mean reliable operation and reduced sticking over time compared with cheap rebuilds. Limitations to note are fitment sensitivity for older models and occasional reports of bleed screw tightness and minor leaks that require careful installation and inspection. The kit includes basic hardware but does not include brake pads or rotors so plan to transfer or purchase compatible pads and perform a full system bleed after fitting.
Best for: A performance-oriented buyer who wants a factory-replacement style rear caliper upgrade that improves durability and appearance while keeping installation straightforward for weekend installers and enthusiasts.
Less Ideal for: Drivers seeking a complete brake system upgrade or a plug-and-play high-performance big-brake conversion should look for kits that include rotors and pads; do not buy if you cannot verify precise fitment for your Eclipse model.
- Direct bolt-on replacement pair with driver and passenger calipers included
- High-temperature powder coat and clear finish for corrosion resistance and improved appearance
- Comes with new seals, boots, guide pins, bleeder screws and mounting hardware for a complete caliper swap
- Pressure tested units and premium lubricated slide pins to reduce sticking and improve longevity
- Does not include brake pads or rotors so additional parts are required for a complete brake job
- Fitment can be vehicle-specific and may require verification to avoid mounting or bracket interference
Verdict: A ready-to-install remanufactured rear caliper pair that combines high-temp powder coating and full hardware to deliver a durable, factory-style performance upgrade.
3. OCPTY Front Brake Caliper Set (Left & Right) for Mitsubishi Eclipse & Galant
| Piston Material | Iron |
|---|---|
| Brake Piston Count | 1 |
| Bleeder Port Size | M10*1.0 |
| Inlet Port Size | M10*1.0 |
| Piston diameter | 2.36 inch |
These OCPTY front brake calipers replace the left and right calipers on compatible Mitsubishi Eclipse and Galant V6 and 2.4L models. They are built with iron pistons and a single-piston design, and use M10*1.0 bleeder and inlet ports for straightforward hose and bleeder fitting. In practice they serve as a direct factory-style replacement that can be bolted in without modifications, so they are suitable for routine repairs or restoring braking on older vehicles. Notable features include durable cast construction and a claimed out-of-the-box fitment for the listed years, which speeds up installation for DIY mechanics or independent shops. The single-piston layout provides predictable stopping power for street use, but it is not a performance multi-piston upgrade. Expect reliable, budget-conscious service life, though finish and long-term corrosion resistance may vary compared with higher-end name-brand calipers. These are a practical option when you want a low-cost, like-for-like replacement to get a Mitsubishi Eclipse back on the road quickly.
Best for: Practical optimizers seeking an affordable, like-for-like factory-style replacement to restore braking on a Mitsubishi Eclipse without upgrades or extra work.
Less Ideal for: Drivers looking for high-performance multi-piston calipers, track use, or the highest corrosion-resistant finishes should consider performance or premium branded options instead.
- Direct fit for quoted Mitsubishi Eclipse and Galant model years for quick replacement
- Cast iron piston construction intended for durability in everyday driving
- Standard M10*1.0 inlet and bleeder ports match common brake line hardware
- Includes both left and right calipers so both sides can be serviced at once
- Single-piston design is not aimed at high-performance braking upgrades
- Surface finish and long-term corrosion protection are unspecified compared with premium brands
Verdict: A cost-conscious, direct-fit front caliper pair that gets compatible Mitsubishi Eclipse and Galant models back on the road with reliable, factory-style braking performance.
4. cciyu Front Right Brake Caliper Assembly with Bracket (Front Passenger)
| Position | Front Right |
|---|---|
| Bleeder Port Size | M10 x 1.0 |
| Inlet Port Size | M10 x 1.0 |
| Piston Count | 1 |
| Piston Material | Iron |
This cciyu front right brake caliper assembly is a plug-in replacement intended to restore braking on compatible Mitsubishi Eclipse and Galant front passenger sides. It ships with the bracket and a single-piston iron piston design sized to match factory fitment, and it uses standard M10 x 1.0 bleeder and inlet ports so it ties into stock brake lines without adapters. In everyday use it provides consistent, quiet braking and is advertised to meet or exceed factory specifications, which makes it suitable for routine repairs or when rebuilding the front brake on one corner. Installation is typical of a caliper swap and may require basic tools and brake fluid bleeding. Limitations include receiving a single caliper (no pads) and the need to confirm fitment for your exact model year and engine; buyers replacing both sides or seeking upgraded multi-piston performance should consider other options.
Best for: Practical, budget-conscious buyers who need an affordable, factory-style replacement caliper to return a Mitsubishi Eclipse or Galant to safe, predictable braking without extra features or upgrades.
Less Ideal for: Drivers seeking a performance brake overhaul, full axle replacement kits that include pads and rotors, or buyers who prefer pre-assembled dual-caliper upgrades should look elsewhere.
- Direct replacement design with included bracket for straightforward installation on the front passenger side
- Standard M10 x 1.0 bleeder and inlet ports that match factory brake lines
- Single iron piston construction provides durable, predictable braking force
- Advertised to meet or exceed factory specifications for consistent stopping and quiet operation
- Sold as a single caliper and does not include brake pads
- Not a performance upgrade — single-piston design limits stopping force compared with multi-piston calipers
Verdict: A budget-friendly, factory-style front right caliper that restores reliable braking on compatible Mitsubishi Eclipse and Galant models but is sold as a single, pad-less unit.
5. SCITOO Rear Left & Right Disc Brake Calipers (Set of 2) Compatible with Mitsubishi Eclipse / Galant
| Position | Rear Driver & Passenger Side |
|---|---|
| OE Number | 19-B3492 19-B3493 |
| Inlet Port Size | M10 x 1 |
| Bleeder Port Size | M7 x 1 |
| Piston Count | 1 Piston |
These SCITOO rear disc calipers replace both left and right units and are intended as a direct-fit factory-quality replacement for specified Mitsubishi Eclipse and Galant models. They arrive painted and include mounting brackets so installation is similar to a factory caliper swap; typical use is as a like-for-like repair when a caliper is seized or leaking. Notable features listed include M10 inlet and M7 bleeder port threads, a single 34.9 mm steel piston per caliper, and factory testing to ISO-like quality standards. In practice the calipers provide predictable stopping force and good pedal feel when paired with correctly sized rotors and pads, and many buyers report straightforward installation. Limitations to consider are that the kit ships without brake pads and relies on proper installation of guide pins and fasteners; a few reports note hardware failure when installation or components are compromised, so plan to inspect and replace mounting hardware and grease pins as needed. For a reliability-first repair this set offers a cost-effective way to restore rear braking function to the covered Mitsubishis.
Best for: Reliability-focused owners seeking a factory-style, cost-conscious rear caliper replacement to restore safe braking on covered Mitsubishi Eclipse and Galant models.
Less Ideal for: Buyers looking for a full brake overhaul or performance upgrade should choose a kit that includes pads, rotors, and upgraded hardware instead of this caliper-only set.
- Sold as a matched left and right pair with mounting brackets for straightforward rear-axle replacement
- Manufactured to factory-spec guidance and factory tested for reliability
- Correct inlet and bleeder port thread sizes (M10 inlet, M7 bleeder) that match factory brake lines and bleeding tools
- Painted finish helps resist corrosion during service life
- Does not include brake pads so additional parts are required for a complete brake job
- Some user reports of broken caliper hardware suggest careful inspection and possible replacement of mounting screws and guide pins during install
Verdict: A matched pair of factory-style rear calipers that provide a practical, reliability-focused replacement for affected Mitsubishi Eclipse and Galant models.
6. Detroit Axle Rear Right Brake Caliper with Bracket for Mitsubishi Eclipse/Galant
| Position | Rear Right |
|---|---|
| Piston Size | 1.37 inch (34.80 mm) |
| Piston Material | Steel |
| Brake Caliper Bracket Included | Yes |
This Detroit Axle rear right caliper is a factory-replacement style assembly sold with its mounting bracket to simplify a one-for-one swap on compatible Mitsubishi Eclipse and Galant vehicles. It uses a single 1.37-inch steel piston and is offered as a complete caliper-plus-bracket kit so you do not need to reuse a worn bracket from the old unit. Typical use is straightforward: remove the old caliper, transfer any needed hardware, bolt the new unit in place, bleed the brake lines, and refit pads and rotor. Practical benefits include durability testing claimed by the maker and a long warranty period, which can give peace of mind for DIY installers who want a ready-to-install part. Reported limitations are occasional missing small items that may need transfer from the old caliper and stiff slide bolts on some units that make pre-removal difficult off-vehicle. The caliper is a focused replacement part rather than an upgraded performance unit, so expect factory-like braking rather than enhanced stopping power or specialty coatings.
Best for: Convenience-driven buyers who want a ready-to-install, vehicle-specific replacement part that minimizes parts hunting and reduces install steps.
Less Ideal for: Drivers seeking performance brake upgrades, specialty coatings, or heavy-duty off-road braking solutions should consider purpose-built aftermarket calipers instead.
- Complete caliper assembly with bracket for easier direct replacement
- Steel piston construction consistent with factory-style durability
- Fits specified Mitsubishi Eclipse and Galant models for straightforward install
- Backed by extended 10-year warranty reported by the manufacturer
- Some buyers report missing small hardware that must be transferred from the old caliper
- Slide bolts may be installed at high torque requiring extra effort to remove during installation
Verdict: A practical, ready-to-install replacement rear caliper for Eclipse owners who prioritize convenience and a factory-style repair.
7. Callahan Rear Brake Kit with Loaded Calipers, Rotors and Ceramic Pads for Mitsubishi Eclipse/Galant
| Position | Rear |
|---|---|
| Includes | 2 calipers, 2 rotors, ceramic pad set with hardware |
| Exterior | Machined |
| Manufacturer | Callahan Brake Parts |
| Model | EBYKC00598 |
This Callahan rear brake kit supplies everything needed to replace rear braking components on compatible Mitsubishi Eclipse and Galant models: two loaded calipers, two precision-machined rotors, and a ceramic pad set with hardware. Installation is typical for a rear brake service job and is intended to provide a direct, factory-quality fit so you can swap components without modification. The rotors are machined and balanced to minimize vibration and the ceramic pads aim for quieter, lower-dust operation compared with semi-metallic pads. Including calipers in the kit removes the need to rebuild or source separate calipers, which simplifies a full rear axle refresh. Limitations are that the kit targets specific model years and rear position only, and a professional installation or mechanical experience is recommended for safe brake work. If you need front components or a different fitment, choose a kit matched to those needs rather than this rear assembly.
Best for: A risk-averse mainstream buyer who wants a single purchase that restores rear braking to factory-like condition with minimal sourcing hassle.
Less Ideal for: Buyers looking to replace front brakes or upgrade to performance rotors and pads should consider a different kit tailored to those goals.
- Complete rear kit includes loaded calipers, rotors and ceramic pads for a single purchase and install.
- Rotors are precision machined and balanced to reduce vibration and improve pedal feel after installation.
- Low-dust ceramic pads promote quieter operation and cleaner wheels compared with many metallic pads.
- Fits only rear position and specific Mitsubishi Eclipse and Galant year ranges, so it is not a universal replacement.
- Requires proper installation and bleeding of the brake system; not a DIY-friendly swap for inexperienced users.
Verdict: A convenient, factory-style rear brake kit that simplifies a full rear brake replacement on supported Mitsubishi Eclipse and Galant models.
Choosing the Right Mitsubishi Eclipse Brake Calipers: Key Factors to Consider
Fitment and Mounting
Correct fitment ensures the caliper mounts securely with the factory brackets and aligns the pads with the rotor. Mismatched mounting points or incorrect piston orientation can cause uneven pad contact, noise, and rapid pad wear.
Check bolt pattern, piston bore size, and caliper offset so the unit clears suspension and wheel components. Proper fitment reduces installation time and avoids the need for additional adapters or machining, which can introduce alignment issues.
Piston and Seal Materials
Piston construction and seal materials affect responsiveness and long-term reliability. Pistons made from stainless steel or coated alloys resist corrosion and stick less often than untreated metals. Seals should be compatible with brake fluid and tolerant of temperature swings to prevent leaks.
Quality seals also influence pedal feel by maintaining consistent hydraulic pressure. Inferior materials can swell, harden, or crack, leading to spongy pedal or fluid loss.
Corrosion Resistance and Finish
Calipers are exposed to water, road salt, and debris, so surface treatment matters for longevity. Protective finishes, plating, or coatings slow rust formation that can seize sliding surfaces or mounting hardware. Corrosion on piston bores or guide pins often leads to sticking calipers and uneven braking.
Consider finishes that balance durability with heat tolerance. Some coatings are primarily cosmetic and will not prevent corrosion in harsh climates, so prioritize proven protective treatments.
Brake Balance and Pad Wear
A well-functioning caliper applies uniform pressure across the pad face to ensure even wear and consistent braking performance. Uneven piston movement or binding guide pins can cause one side of a pad to wear faster, reducing service life and affecting stopping balance between wheels.
When selecting calipers, consider how design and machining tolerances influence pad contact and whether the caliper supports the pad size and rotor thickness used on your Mitsubishi Eclipse.
Serviceability and Parts Availability
Access to rebuild kits, replacement seals, and guide pins extends a caliper's usable life and can reduce long-term ownership costs. Remanufactured or serviceable calipers allow routine maintenance such as seal replacement without full unit swap.
Verify that common wear components are readily available and that the caliper design permits straightforward maintenance with standard tools. This factor matters for owners who prefer to perform repairs themselves or who expect long-term ownership.
Compatibility with Brake Hardware and Pads
Calipers must work with the correct pad profile, caliper brackets, and rotor dimensions to function as intended. Differences in pad backing plate thickness, shim requirements, or mounting clip shape can affect fit and noise.
Confirm compatibility with the brake hardware used on the Mitsubishi Eclipse, including parking brake mechanisms if applicable. Ensuring the caliper accepts standard hardware simplifies replacement and reduces the chance of installation issues.
How We Chose the Best Mitsubishi Eclipse Brake Calipers
We prioritized items that provide correct fitment and mounting alignment for the Mitsubishi Eclipse, along with robust piston and seal materials to resist seizing. Stopping performance under repeated use and even pad wear were key functional criteria, since inconsistent caliper action directly affects braking balance. We also evaluated corrosion resistance and finish quality because exposure to road salt and moisture shortens component life. Ease of installation and availability of compatible hardware or rebuild kits were considered to help owners who plan maintenance.We excluded parts lacking clear vehicle fitment data, items without documented material specifications, and options that required extensive modification. The final selections balance durability, functionality, and serviceability while focusing specifically on components designed to meet the Mitsubishi Eclipse's mounting and clearance requirements.
Our full evaluation process is outlined in our review methodology.
FAQ
How do I know if a caliper fits my Mitsubishi Eclipse?
Check the caliper's listed vehicle fitment and verify bolt pattern, piston bore size, and mounting orientation match the Eclipse specifications. Look for documentation that confirms fit for your model year and trim, and compare mount hole spacing to the factory bracket to avoid clearance issues.
What are common brake caliper symptoms that indicate replacement?
Typical signs include an uneven brake pedal, dragging or reduced braking on one side, fluid leaks near the caliper, and visible corrosion or seized guide pins. You may also notice uneven pad wear or a persistent vehicle pull during braking, which often points to caliper problems.
Can I use remanufactured brake calipers on the Mitsubishi Eclipse?
Remanufactured calipers are often a practical option if they have been rebuilt to proper specifications and include inspected pistons, new seals, and corrosion protection. Ensure the remanufactured unit lists explicit fitment for the Eclipse and comes with a warranty or parts guarantee.
Is it worth rebuilding a caliper instead of replacing it?
Rebuilding can be cost effective when the caliper body and piston are in good condition but seals, boots, or guide pins need renewal. A rebuild kit restores sealing surfaces and sliding components, but consider corrosion extent and overall caliper integrity before opting to rebuild.
What tools do I need for brake caliper replacement on the Eclipse?
Common tools include a basic metric socket set, torque wrench, C-clamp or piston tool for compressing pistons, brake line wrench, and brake cleaner. Have new seals or hardware on hand if required, and follow safe bleeding procedures to remove air from the system after installation.
How can I prevent caliper sticking symptoms in the future?
Regularly inspect and clean guide pins, keep sliding surfaces lubricated with high-temperature brake grease, and address corrosion promptly. Using protective coatings or choosing calipers with robust finishes helps reduce the chance of pistons and pins seizing over time.
Conclusion
When selecting brake calipers for a Mitsubishi Eclipse, prioritize correct fitment, corrosion resistance, and quality piston and seal materials. These dimensions most directly affect braking balance, pedal feel, and long-term reliability.Also weigh serviceability and parts availability because access to rebuild kits and replacement hardware can extend the unit's life and simplify maintenance. Balance immediate performance needs with how you plan to maintain the braking system over time.
Explore More:
- Check out all Mitsubishi Eclipse parts & accessories
- Explore Brake Calipers Maintenance & Repair Guides
- Explore Brake System
- Browse all Auto Parts
